? semiconductor components industries, llc, 2012 august, 2012 ? rev. 1 1 publication order number: ns5b1g384/d ns5b1g384 single (nc) normally closed spst analog switch the ns5b1g384 is single pole single throw (spst) high-speed ttl-compatible switch. the low resistance and capacitance characteristics of this switch make it ideal for low-distortion audio, video, and data routing applications. the switch has a normally closed logic configuration meaning the switch is on (nc connected to com) when in is low. these switches are available in 5-pin sc ? 70 and 5-pin tsop ? 5 (sot23 ? 5) packages for operation over the industrial (-40 c to +85 c) temperature range. features ? v cc operating range: 2.0 v to 5.5 v ? low on resistance : r on : 4.0 typical @ v cc = 4.5 v ? minimal propagation delay : t pd < 0.5 ns ? control input compatible with ttl levels ? esd performance: human body model > 2 kv ? 5-pin sc ? 70 or 5-pin tsop ? 5 packages available ? these are pb ? free devices typical applications ? audio, video, and high-speed data switching ? mobile phones ? portable devices ? desktop & notebook computing http://onsemi.com see detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. ordering information pin assignments marking diagrams sc ? 70 case 419a ag = for sc ? 70 ad = for tsop ? 5 m = date code = pb ? free package com in nc logic diagram 1 5 tsop ? 5 (sot23 ? 5) case 483 1 5 ad m ag m (note: microdot may be in either location) v cc com nc in gnd 1 2 3 5 4
ns5b1g384 http://onsemi.com 2 pin description pin # name direction description 1 com i/o common signal line 2 nc i/o normally closed signal line 3 gnd input ground 4 in input control signal line 5 v cc input voltage supply truth table in control input function l nc connected to com h nc disconnected from com maximum ratings symbol pins rating value condition unit v cc v cc positive dc supply voltage ? 0.5 to +7.0 v v is nc or com analog signal voltage ? 0.5 to v cc + 0.5 v v in in control input voltage ? 0.5 to +7.0 v i is_con nc or com analog signal continuous current 300 closed switch ma i is_pk nc or com analog signal peak current 500 10% duty cycle ma i in in control input current 20 ma t stg storage temperature range ? 65 to 150 c stresses exceeding maximum ratings may damage the device. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect device reliability. recommended operating conditions symbol pins parameter value condition unit v cc v cc positive dc supply voltage 2.0 to 5.5 v v is nc or com analog signal voltage gnd to v cc v v in in control input voltage gnd to 5.5 v t a operating temperature range ? 40 to +85 c t r , t f input rise or fall time 20 v cc = 3.3 v ns/v 10 v cc = 5.0 v minimum and maximum values are guaranteed through test or design across the recommended operating conditions , where applicable. typical values are listed for guidance only and are based on the particular conditions listed for each section, whe re applicable. these conditions are valid for all values found in the characteristics tables unless otherwise specified in the tes t conditions. esd protection pins description minimum voltage all pins human body model 2 kv
ns5b1g384 http://onsemi.com 3 dc electrical characteristics control input (typical: t = 25 c) symbol pins parameter test conditions v cc (v) ? 40 c to +85 c unit min typ max v ih in control input high 4.5 ? 5.5 2.0 v v il in control input low 4.5 ? 5.5 0.8 v i in in control input leakage 0 v in v cc 5.0 0.1 0.5 a supply current and leakage (typical: t = 25 c) symbol pins parameter test conditions v cc (v) ? 40 c to +85 c unit min typ max i nc (off) nc off state leakage v in = v il or v ih v nc = 1.0 v v com = 4.5 v 5.5 10 100 na i com (off) com off state leakage v in = v il or v ih v nc = 4.5 v v com = 1.0 v 5.5 10 100 na i cc v cc quiescent supply v in and v is = v cc or gnd i d = 0 a 2.0 ? 5.5 0.1 1.0 a i off in power off leakage v in = 5.5 v or gnd 0 0.5 1.0 a on resistance (typical: t = 25 c) symbol pins parameter test conditions v cc (v) ? 40 c to +85 c unit min typ max r on nc, com on resistance v is = 0 v, i on = 30 ma v is = 0 v, i on = 64 ma v is = 2.4 v, i on = 15 ma 4.5 4.5 4.5 4.0 4.0 11.5 7.0 7.0 15
ns5b1g384 http://onsemi.com 4 ac electrical characteristics timing/frequency (typical: t = 25 c, r l = 50 , c l = 35 pf, f = 1 mhz) symbol pins parameter test conditions v cc (v) ? 40 c to +85 c unit min typ max t on in to nc turn on time as above, figures 1 and 2 4.5 6.0 ns t off in to nc turn off time as above, figures 1 and 2 4.5 2.0 ns t pd nc to com propagation delay 4.5 0.5 ns bw ? 3db bandwidth c l = 5 pf, figures 3 and 4 4.5 330 mhz capacitance (typical: t = 25 c, r l = 50 , c l = 5 pf, f = 1 mhz) symbol pins parameter test conditions v cc (v) ? 40 c to +85 c unit min typ max c in in control input 0 v 2.2 pf c on nc to com through switch v in = 0v 4.5 v 12 pf c off nc unselected port v is = 4.5 v, v in = 4.5 v 4.5 v 4.1 pf device ordering information device order number package type tape & reel size ? ns5b1g384dft2g sc ? 70 (pb ? free) 3000 / tape & reel NS5B1G384DTT1G tsop ? 5 (pb ? free) 3000 / tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d.
ns5b1g384 http://onsemi.com 5 figure 1. t on /t off 50% 50% 90% 90% t on t off v oh output input v cc 0 v figure 2. t on /t off dut open 35 pf v cc input 50% 50% 10% t on t off output input v cc 0 v 10% 50 output v ol v out v oh v ol dut open v cc input output 50 35 pf v out 0.1 f channel switch control/s test socket is normalized. off isolation is measured across an off channel. on loss is the bandwidth of an on switch. v iso , bandwidth and v onl are independent of the input signal direction. v iso = off channel isolation = 20 log for v in at 100 khz v onl = on channel loss = 20 log for v in at 100 khz to 50 mhz bandwidth (bw) = the frequency 3 db below v onl v ct = use v iso setup and test to all other switch analog input/outputs terminated with 50 output dut input 50 50 generator reference transmitted figure 3. off channel isolation/on channel loss (bw)/crosstalk (on channel to off channel)/v onl 50 v out v in v out v in
ns5b1g384 http://onsemi.com 6 ? 6 ? 5 ? 4 ? 3 ? 2 ? 1 0 10000 1000000 100000000 frequency (hz) magnitude (db) figure 4. typical bandwidth @ v cc = 5.5 v, 25 c ? 100 ? 90 ? 80 ? 70 ? 60 ? 50 ? 40 ? 30 ? 20 ? 10 10000 1000000 100000000 frequency (hz) figure 5. off ? channel isolation @ v cc = 5.5 v, 25 c magnitude (db) 0 0.01 0.02 0.03 0.04 0.05 0.06 10 100 1000 10000 100000 frequency (hz) figure 6. typical total harmonic distortion @ v cc = 4.5 v percent (%)
ns5b1g384 http://onsemi.com 7 package dimensions sc ? 88a (sc ? 70 ? 5/sot ? 353) case 419a ? 02 issue k notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: inch. 3. 419a ? 01 obsolete. new standard 419a ? 02. 4. dimensions a and b do not include mold flash, protrusions, or gate burrs. dim a min max min max millimeters 1.80 2.20 0.071 0.087 inches b 1.15 1.35 0.045 0.053 c 0.80 1.10 0.031 0.043 d 0.10 0.30 0.004 0.012 g 0.65 bsc 0.026 bsc h --- 0.10 --- 0.004 j 0.10 0.25 0.004 0.010 k 0.10 0.30 0.004 0.012 n 0.20 ref 0.008 ref s 2.00 2.20 0.079 0.087 b 0.2 (0.008) mm 12 3 4 5 a g s d 5 pl h c n j k ? b ?
ns5b1g384 http://onsemi.com 8 package dimensions tsop ? 5, sot23 ? 5 case 483 ? 02 issue h notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. maximum lead thickness includes lead finish thickness. minimum lead thickness is the minimum thickness of base material. 4. dimensions a and b do not include mold flash, protrusions, or gate burrs. 5. optional construction: an additional trimmed lead is allowed in this location. trimmed lead not to extend more than 0.2 from body. dim min max millimeters a 3.00 bsc b 1.50 bsc c 0.90 1.10 d 0.25 0.50 g 0.95 bsc h 0.01 0.10 j 0.10 0.26 k 0.20 0.60 l 1.25 1.55 m 0 10 s 2.50 3.00 123 54 s a g l b d h c j 0.7 0.028 1.0 0.039 mm inches scale 10:1 0.95 0.037 2.4 0.094 1.9 0.074 *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. soldering footprint* 0.20 5x c ab t 0.10 2x 2x t 0.20 note 5 t seating plane 0.05 k m detail z detail z on semiconductor and are registered trademarks of semiconductor co mponents industries, llc (scillc). scillc owns the rights to a numb er of patents, trademarks, copyrights, trade secrets, and other intellectual property. a list ing of scillc?s product/patent coverage may be accessed at ww w.onsemi.com/site/pdf/patent ? marking.pdf. scillc reserves the right to make changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and s pecifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. all operating parame ters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or a uthorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in whic h the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or us e scillc products for any such unintended or unauthorized appli cation, buyer shall indemnify and hold scillc and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unin tended or unauthorized use, even if such claim alleges that scil lc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyrig ht laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5817 ? 1050 ns5b1g384/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative
|
